Pass4Test est un site professionnel qui répondre les demandes de beaucoup clients. Les candidats qui ont déjà passer leurs premiers test Certification IT ont devenus les suivis de Pass4Test. Grâce à la bonne qualité des documentations, Pass4Test peut aider tous candidats à réussir le test HP HP0-207.
Pour vous laisser savoir mieux que la Q&A HP HP0-207 produit par Pass4Test est persuadante, le démo de Q&A HP HP0-207 est gratuit à télécharger. Sous l'aide de Pass4Test, vous pouvez non seulement passer le test à la première fois, mais aussi économiser vos temps et efforts. Vous allez trouver les questions presque même que lesquels dans le test réel. C'est pourquoi tous les candidats peuvent réussir le test HP HP0-207 sans aucune doute. C'est aussi un symbole d'un meilleur demain de votre carrière.
Code d'Examen: HP0-207
Nom d'Examen: HP (Procurve Adaptive EDGE Fundamentals)
Questions et réponses: 120 Q&As
Beaucoup de travailleurs dans l'Industrie IT peut obenir un meilleur travail et améliorer son niveau de vie à travers le Certificat HP HP0-207. Mais la majorité des candidats dépensent beaucoup de temps et d'argent pour préparer le test, ça ne coûte pas dans cette société que le temps est tellement précieux. Pass4Test peut vous aider à économiser le temps et l'effort pendant le cours de la préparation du test HP HP0-207. Choisir le produit de Pass4Test particulier pour le test Certification HP HP0-207 vous permet à réussir 100% le test. Votre argent sera tout rendu si malheureusement vous ne passez pas le test.
Le test HP HP0-207 est test certification très répandu dans l'industrie IT. Vous pourriez à améliorer votre niveau de vie, l'état dans l'industrie IT, etc. C'est aussi un test très rentable, mais très difficile à réussir.
Vous aurez le service de la mise à jour gratuite pendant un an une fois que vous achetez le produit de Pass4Test. Vous pouvez recevoir les notes immédiatement à propos de aucun changement dans le test ou la nouvelle Q&A sortie. Pass4Test permet tous les clients à réussir le test HP HP0-207 à la première fois.
Est-que vous s'inquiétez encore à passer le test Certification HP0-207 qui demande beaucoup d'efforts? Est-que vous travaillez nuit et jour juste pour préparer le test de HP HP0-207? Si vous voulez réussir le test HP HP0-207 plus facilement? N'hésitez plus à nous choisir. Pass4Test vous aidera à réaliser votre rêve.
HP0-207 Démo gratuit à télécharger: http://www.pass4test.fr/HP0-207.html
NO.1 What are the key principles of the Adaptive EDGE architecture? Select TWO.
A.Control to the Edge
B.Control to the Desktop
C.Command from the Center
D.Management from Anywhere
E.Security throughout the Network
Correct:A C
certification HP HP0-207 HP0-207 examen
NO.2 You are assigned to configure ProCurve switches at a customer site for in-band management.
Which are in-band management methods? Select TWO.
A.Telnet
B.SNMP
C.XMODEM
D.serial console
E.menu interface
Correct:A B
certification HP HP0-207 HP0-207 examen
NO.3 On switches that support the Switch Setup screen interface, which parameters can be
configured on the Switch Setup screen? Select TWO.
A.STP bridge priority
B.IP address of the TACACS+ server
C.system name and contact information
D.IP address and subnet mask for each VLAN
E.IP address and subnet mask for the default VLAN
Correct:C E
certification HP HP0-207 HP0-207 examen
NO.4 You have been asked to configure IGMP on a ProCurve Switch 6200yl at a customer site. What
are the steps for enabling IGMP on the switch?
A.Enter the manager level, then issue the ip igmp command.
B.Enter the global configuration context, then issue the ip igmp command.
C.Enter the VLAN context for each VLAN that will support IGMP, then issue the ip igmp command.
D.Enter the interface configuration context for each port configured with a VLAN, then issue the ip igmp
command.
Correct:C
certification HP HP0-207 HP0-207 examen
NO.5 While using the CLI to configure a ProCurve switch, you must change context from the manager
level to the global configuration level. Which command do you use?
A.exit
B.write
C.global
D.enable
E.configure
Correct:E
certification HP HP0-207 HP0-207 examen
NO.6 While examining the spanning tree configuration on a ProCurve switch, you notice that one of
the ports is in the Blocking state. Which statement describes how this port will function in this
state?
A.The port is completely blocked for all purposes.
B.The switch will not forward user traffic through that port, but will forward telnet traffic.
C.The switch will not forward user traffic through that port, but will forward BPDUs through that port.
D.The switch forwards user traffic through that port, but does not receive user traffic through that port.
Correct:C
certification HP HP0-207 HP0-207 examen
NO.7 You must remotely manage a customer's switch using Telnet. Which configuration/monitoring
interfaces are available? Select TWO.
A.web interface
B.menu interface
C.ProCurve Manager
D.boot monitor interface
E.command line interface
Correct:B E
certification HP HP0-207 HP0-207 examen
NO.8 While using the CLI to configure a ProCurve switch, you must move from the global
configuration level to the port context configuration level for port a1. Which command do you use?
A.port a1
B.ethernet a1
C.interface a1
D.configure a1
Correct:C
certification HP HP0-207 HP0-207 examen
NO.9 At a customer site, you have configured four ProCurve switches for HP Switch Meshing and
Multiple Spanning Tree Protocol. How will the mesh appear to non-mesh switches in the same
spanning tree domain?
A.as a single device
B.as a set of devices without redundant links
C.as devices that cannot participate in the spanning tree
D.as a set of devices with spanning tree enabled to block redundant links
Correct:A
certification HP HP0-207 HP0-207 examen
NO.10 You are installing a ProCurve switch at a customer site and must enable remote management
for network administrators. Which configuration parameter is necessary to ensure that
administrators can manage the switch even if they are on different IP networks?
A.default VLAN
B.default gateway
C.default password
D.default management profile
Correct:B
certification HP HP0-207 HP0-207 examen
NO.11 A customer is planning a Power over Ethernet deployment for a large call center that will use
VoIP telephones. While planning the wiring closets for the deployment, the customer suggests
using the uplink ports of a ProCurve Switch 2650-PWR to provide power to a ProCurve Switch
2600-8-PWR. Which statement describes a correct response to this suggestion?
A.It is only possible if the second switch is a ProCurve Switch 2626-PWR.
B.It is not possible because the 2600-8-PWR cannot act as a Powered Device.
C.It is only possible if the customer adds a ProCurve 600 EPS/RPS to the first switch.
D.It is not recommended because the second switch will not have adequate power redundancy.
Correct:B
certification HP HP0-207 HP0-207 examen
NO.12 How is traffic prioritization accomplished with IEEE 802.1p?
A.802.1Q-compliant devices enforce priorities based on VLAN ID.
B.802.1Q-compliant devices set one of 8 values in a 3-bit field in the VLAN tag.
C.802.1Q-compliant devices set one of 64 values in a 6-bit field in the IP datagram header.
D.802.1Q-compliant devices dedicate a portion of available bandwidth to each prioritized conversation.
Correct:B
certification HP HP0-207 HP0-207 examen
NO.13 You are about to configure HP Switch Meshing on four ProCurve switches at a customer site.
All of the ports that will be included in the mesh are configured for membership in customer
VLANs. How will the mesh configuration affect the VLAN configuration?
A.The mesh ports will automatically become a tagged member of all configured VLANs.
B.The mesh ports will not be a member of any VLANs until you manually configure its VLAN assignments.
C.The mesh ports will not be 802.1Q-compliant and will only be able to retain membership in a single
untagged VLAN.
D.The mesh ports will automatically become a member of the default VLAN and must be configured for
other VLAN membership.
Correct:A
certification HP HP0-207 HP0-207 examen
NO.14 How do ProCurve switches, configured with link aggregation (also known as port trunking),
handle broadcast traffic?
A.Broadcast traffic is flooded through all of the ports in the trunk.
B.The switch sends a query and receives permission from potential receivers before flooding.
C.Broadcast traffic is handled in exactly the same way it would be without port trunking configured.
D.Broadcast traffic is flooded through non-trunked ports, but forwarded only through one of the ports in
the trunk.
Correct:D
certification HP HP0-207 HP0-207 examen
NO.15 You are configuring a ProCurve Layer 2 switch to obtain time information from an SNTP server
located on a different IP network than the switch. Which configuration steps are necessary on the
switch to enable this functionality?
A.The switch cannot be configured to obtain time information from a server on a different IP network.
B.Define a default gateway for the switch, enable SNTP, use the sntp server command to enter the IP
address of the server.
C.Assign a port on the switch to a VLAN that includes the SNTP server, enable SNTP, configure the
switch for SNTP unicast mode.
D.Configure an IP address on the same IP network as the SNTP server, enable TimeP, configure the
switch for SNTP broadcast mode.
Correct:B
certification HP HP0-207 HP0-207 examen
NO.16 You are implementing a fully connected HP Switch Mesh at a customer site. Which statement
describes a valid design guideline for HP Switch Meshing?
A.A switch may be connected to no more than four mesh domains.
B.Up to five Switch 5400zl Series switches can be included in a full mesh.
C.All links in a full mesh must operate at the same speed and use the same media type.
D.When a switch is configured for HP Switch Meshing protocol, all of the ports on that switch must
participate in the mesh.
Correct:B
certification HP HP0-207 HP0-207 examen
NO.17 You must update the software on a customer's ProCurve Switch 5412zl. Which statement
correctly describes the process for this operation? Select TWO.
A.Use TFTP for direct serial transfer of the software.
B.Use FTP for in-band transfer of the software through an IP network.
C.Use TFTP for in-band transfer of the software through an IP network.
D.Transfer the software from your workstation using a direct serial transfer.
E.Instruct the switch to search for any available TFTP server without knowing its IP address.
Correct:C D
certification HP HP0-207 HP0-207 examen
NO.18 You configured Rapid Spanning Tree Protocol on four ProCurve Switch 5348xl switches at a
customer site. During the configuration, you forgot to configure the switches so that
switch-to-switch links are not defined as edge ports. Which statement describes the consequence
of your oversight?
A.The switches in the spanning tree will elect multiple Root bridges.
B.The switches will reject the spanning tree configuration and block all ports until the configuration is
corrected.
C.The switches will be unable to elect a Root bridge and will not be able to forward traffic until the
configuration is corrected.
D.The switches will require more time to elect the Root bridge and resolve the topology, but the spanning
tree will otherwise function normally.
Correct:D
certification HP HP0-207 HP0-207 examen
NO.19 What are the primary solution categories of the Adaptive EDGE Architecture? Select THREE.
A.mobility
B.security
C.reliability
D.availability
E.upgradeability
F.convergence
G.cost-effectiveness
Correct:A B F
certification HP HP0-207 HP0-207 examen
NO.20 You are about to update the software on a ProCurve switch. Which command do you use to view
a list of all software versions stored on the switch?
A.show run
B.show flash
C.show startup
D.show version
Correct:B
certification HP HP0-207 HP0-207 examen
Choisir le Pass4Test peut vous aider à réussir 100% le test HP HP0-207 qui change tout le temps. Pass4Test peut vous offrir les infos plus nouvelles. Dans le site de Pass4Test le servie en ligne est disponible toute la journée. Si vous ne passerez pas le test, votre argent sera tout rendu.
没有评论:
发表评论